[MicroServer G7 N54L] VMWARE에서 HDD 추가 / 마운트 까지...
우선 Power Off 합니다. 그리고
상단 메뉴중 VM -> Setting (CTRL + D) -> ADD -> Hard Disk -> Next -> Next -> Next -> 용량 선택 -> Finish
이렇게 하면 HDD는 추가 한겁니다.
다시 Power On.
그리고 ssh로 접속해서 fdisk -l 을 하면 아래와 같이 나옵니다.
fdisk -l 현재 장착되어 있는 disk를 보여주는 명령어 입니다.
[root@localhost qual]# fdisk -l
Disk /dev/sda: 21.5 GB, 21474836480 bytes
255 heads, 63 sectors/track, 2610 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0000f560
Device Boot Start End Blocks Id System
/dev/sda1 * 1 1045 8387584 83 Linux
/dev/sda2 1045 2350 10485760 83 Linux
/dev/sda3 2350 2611 2097152 82 Linux swap / Solaris
Disk /dev/sdb: 106 MB, 106954752 bytes
64 heads, 32 sectors/track, 102 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Disk /dev/sdb doesn't contain a valid partition table
[root@localhost qual]#
[root@localhost qual]# fdisk /dev/sdb
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel with disk identifier 0x996eed0e.
Changes will remain in memory only, until you decide to write them.
After that, of course, the previous content won't be recoverable.
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
WARNING: DOS-compatible mode is deprecated. It's strongly recommended to
switch off the mode (command 'c') and change display units to
sectors (command 'u').
Command (m for help):
n => 새로운 파티션을 만듭니다.
- p => 기본 파티션 생성
- e => 확장 파티션 생성
w => 파티션 테이블 설정 저장
[root@localhost qual]# fdisk /dev/sdb
Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel
Building a new DOS disklabel with disk identifier 0xd4f54031.
Changes will remain in memory only, until you decide to write them.
After that, of course, the previous content won't be recoverable.
Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)
WARNING: DOS-compatible mode is deprecated. It's strongly recommended to
switch off the mode (command 'c') and change display units to
sectors (command 'u').
Command (m for help): n => 새로운 파티션 생성
Command action
e extended
p primary partition (1-4)
p => 기본 파티션 생성
Partition number (1-4): 1 => 파티션 번호
First cylinder (1-102, default 1):
Using default value 1 => 하드디스크 용량 시작점.
Last cylinder, +cylinders or +size{K,M,G} (1-102, default 102):
Using default value 102 => 하드디스크 용량 끝. (100메가 하드 디스크 추가)
Command (m for help): w => 파티션 테이블 설정 저장(위에 설정한것 저장)
The partition table has been altered!
Calling ioctl() to re-read partition table.
Syncing disks.
[root@localhost qual]# fdisk -l
Disk /dev/sda: 21.5 GB, 21474836480 bytes
255 heads, 63 sectors/track, 2610 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x0000f560
Device Boot Start End Blocks Id System
/dev/sda1 * 1 1045 8387584 83 Linux
/dev/sda2 1045 2350 10485760 83 Linux
/dev/sda3 2350 2611 2097152 82 Linux swap / Solaris
Disk /dev/sdb: 106 MB, 106954752 bytes
64 heads, 32 sectors/track, 102 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0xd4f54031
Device Boot Start End Blocks Id System
/dev/sdb1 1 102 104432 83 Linux => 추가로 /dev/sdb1로 생성됨.
[root@localhost qual]#
마지막에 w를 하고 파티션 설정을 꼭 저장해야 됩니다.
이제 디스크를 추가 했으니 사용하기전에 포멧을 해야합니다.
파일 시스템 포멧 명령어
mkfs -t [파일 시스템] [파티션 경로]
ex) 파일 시스템(ext3/ext4 등등등)
[root@localhost /]# mkfs -t ext4 /dev/sdb1
mke2fs 1.41.12 (17-May-2010)
Filesystem label=
OS type: Linux
Block size=1024 (log=0)
Fragment size=1024 (log=0)
Stride=0 blocks, Stripe width=0 blocks
26208 inodes, 104432 blocks
5221 blocks (5.00%) reserved for the super user
First data block=1
Maximum filesystem blocks=67371008
13 block groups
8192 blocks per group, 8192 fragments per group
2016 inodes per group
Superblock backups stored on blocks:
8193, 24577, 40961, 57345, 73729
Writing inode tables: done
Creating journal (4096 blocks): done
Writing superblocks and filesystem accounting information: done
This filesystem will be automatically checked every 28 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
[root@localhost /]#
파일 시스템 확인 명령어
file -s [파티션 경로]
[root@localhost /]# file -s /dev/sda1
/dev/sda1: Linux rev 1.0 ext4 filesystem data (needs journal recovery) (extents) (large files) (huge files)
[root@localhost /]#
이제 파티션을 추가하고 포멧도 했습니다.
추가한 하드를 쓰려면 이제 마운트(MOUNT) 하면 됩니다.
마운트를 하기위해 디렉토리를 만듭니다.
[root@localhost /]# mkdir Backup
[root@localhost /]# ls
Backup bin boot cgroup dev etc home lib lost+found media misc mnt net opt proc root sbin selinux srv sys tmp usr var
[root@localhost /]#
마운트 명령어
mount [파티션 경로] [마운트 할 경로]
[root@localhost /]# mount -t ext4 /dev/sdb1 /Backup
마운트 정보 확인
df -h
[root@localhost /]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda1 7.8G 3.7G 3.7G 51% /
tmpfs 504M 72K 504M 1% /dev/shm
/dev/sda2 9.8G 24M 9.2G 1% /home
[root@localhost /]# mount /dev/sdb1 /Backup
[root@localhost /]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda1 7.8G 3.7G 3.7G 51% /
tmpfs 504M 72K 504M 1% /dev/shm
/dev/sda2 9.8G 24M 9.2G 1% /home
/dev/sdb1 95M 1.6M 87M 2% /Backup => mount로 새롭게 추가!!
[root@localhost /]#
이렇게 하면 끝!!!
하지만!! 이건 일시적인것 뿐...
재부팅을 하면 마운트를 다시 해야 합니다.
재시작을 해도 마운트가 풀리지 않도록 fstab에 등록하면 됩니다.
vi /etc/fstab
#
# /etc/fstab
# Created by anaconda on Sat Oct 4 20:51:39 2014
#
# Accessible filesystems, by reference, are maintained under '/dev/disk'
# See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info
#
UUID=cba4e03b-05d6-4b79-ace8-8955caf5f295 / ext4 defaults 1 1
UUID=d316c840-a6c0-443f-b5cd-64a1c0eded2d /home ext4 defaults 1 2
UUID=25c07c8b-002b-43a8-ab41-a7790ec6307d swap swap defaults 0 0
/dev/sdb1 /Backup ext4 defaults 0 0 => 추가
tmpfs /dev/shm tmpfs defaults 0 0
devpts /dev/pts devpts gid=5,mode=620 0 0
sysfs /sys sysfs defaults 0 0
proc /proc proc defaults 0 0
SP64420.zip
